Alpolic FR is supplied by PSP for use as part of an external wall cladding system, or as an internal wall lining, including in wet areas.

When used as an external cladding the follow scope of use applies:

Location:

• In wind zones up to and including extra high as defined in NZS 3604:2011 or calculated design wind pressure (ULS) of 2.5kPa
• In all exposure zones as defined in NZS 3604:2011
• On buildings at least 1m from the relevant boundary

Building:

• In conjunction with a primary structure that complies with the NZ Building Code or where the designer has established that the existing structure is suitable for the intended building work
• As an external wall cladding, on buildings up to 10m in building height and in conjunction with a drained and ventilated cavity

Show more

If designed, installed and maintained in accordance with all PSP requirements, the Alpolic FR will comply with or contribute to compliance with the following performance claims:

• B1 Structure: B1.3.1 B1.3.2 B1.3.3 (a, b, c, e, f, h, j, m) B1.3.4 (a, b, c, d, e)
  Verification method: B1/VM1
  • Tested by James Cook University to AS/NZS 4040:1996 for serviceability and cyclic strength wind loading
  • AS/NZS 4040:1996 is cited in AS/NZS 1170.2:2011
  • James Cook University is NATA accredited
• B2 Durability: B2.3.2 (b)
  Alternative solution
  • Demonstrated by Mitsubishi Plastics Material safety data sheet MSDS No LL75-0002 and Summary of specification data
• C3 Fire Affecting Areas Beyond the Source: C3.4 (a)
  Acceptable solution C/AS1, C/AS2 1st edition June 2019
  • Tested to EN 13501-1:2007 by AFITI LICOF achieving A2-s1, d0 classification, equivalent to Group 1-S as provided for by MBIE guidance
  • AFITI LICOF Center For Fire Testing and Research is ILAC accredited
• E2 External Moisture: E2.3.2 E2.3.3 E2.3.5 E2.3.7 (a, b, c)
  Verification method E2/VM1
  • Tested in accordance with AS/NZS 4284:2008 by Façade Lab (IANZ accredited)
• E3 Internal Moisture: E3.3.4, E3.3.5, E3.3.6
  Alternative solution
  • Aluminium is impervious to moisture
  • Mitsubishi Plastics Material safety data sheet MSDS No LL75-0002
• F2 Hazardous Building Materials: F2.3.1
  Alternative solution
  • Material is inert and passed combustion toxicity testing
  • Mitsubishi Plastics Material safety data sheet MSDS No LL75-0002
• G3 Food Preparation and Prevention of Contamination: G3.3.2 (a, b)
  Alternative solution
  • The coating system does not support the growth of bacteria of fungi
  • Mitsubishi Plastics Summary of specification data

• Tested by James Cook University to AS/NZS 4040:1996 for serviceability and cyclic strength wind loading
• AS/NZS 4040:1996 is cited in AS/NZS 1170.2:2011
• James Cook University is NATA accredited

• Demonstrated by Mitsubishi Plastics Material safety data sheet MSDS No LL75-0002 and Summary of specification data

• Tested to EN 13501-1:2007 by AFITI LICOF achieving A2-s1, d0 classification, equivalent to Group 1-S as provided for by MBIE guidance
• AFITI LICOF Center For Fire Testing and Research is ILAC accredited

• Tested in accordance with AS/NZS 4284:2008 by Façade Lab (IANZ accredited)

• Aluminium is impervious to moisture
• Mitsubishi Plastics Material safety data sheet MSDS No LL75-0002

• Material is inert and passed combustion toxicity testing
• Mitsubishi Plastics Material safety data sheet MSDS No LL75-0002

• The coating system does not support the growth of bacteria of fungi
• Mitsubishi Plastics Summary of specification data

Show more

External Moisture