You are using an outdated browser version not supported by this website.
Click here to upgrade your browser

NZ Foam Shed Conversion Insulation 70mm-R-3.13, 80mm-R-3.57, 100mm-R-4.46
Description

NZ Foam Shed Conversion insulation system provides a cost saving alternative system which can control the internal temperature of your existing/new shed. A spray-in-place insulation provides a durable air-tight barrier. The foam is a closed cell, medium density 2-part polyurethane foam with low thermal conductivity that will adhere to numerous substrates.

NZ Foam products not only provides thermal insulation but creates an air and moisture seal, giving greater control over the interior environment of the shed.

Key Features

Performance benefits:

  • Stable thermal performance
  • No need to remove existing claddings as existing shed can be converted to high tech cool stores
  • Meets fire test standard AS1366
  • Completely inert within 24 hours and no further off-gasing
  • High R-values as required by the New Zealand Building Code (NZBC)(1) 
    • 70mm — R-value 3.13
    • 80mm — R-value 3.57
    • 100mm — R-value 4.46
  • Good sound control
  • Maintains an air seal even after seasonal expansion/contraction of building assembly
  • Less than 1% water absorption
  • Supports indoor air quality by blocking air infiltration and mass transfer of moisture that may cause mould

Characteristics:

  • Closed cell semi-rigid structure
  • Medium density (2lb)
  • Expands ~30 times from liquid state
  • Application thickness is not limited
  • Will not harm electrical wiring, plumbing or other building components
  • Low global warming potential
Scope of Use

The product is usually site applied using special spray equipment, trained applicators and under strict quality control conditions.

Typically used for application into timber, concrete and/or light gauge steel framing of walls, floors, and in roofs to meet thermal performance design requirements.

Limitations on Use

Subject to the following:

  • All designs and construction shall be within the requirements and the guidelines set out in the ASCC Technical Manual ver 1.1 dated 1 July 2016, which includes ensuring the substrate to be properly assessed before application. Other uses are outside the scope of this certificate.
  • For application to light gauge steel framing, using a 400mm stud spacing and 63mm product, a 0.7 R-value thermal break is re-quired in all climate zones, and for 600mm stud spacings using 90mm thickness of product a .5 R-value thermal break is required in all climate zones.
  • Substrates are to comply with those specified in the ASCC Technical Manual ver 1.1 dated 1 July 2016, and the ASCC Building Product Quality Plan ver 2.1;
  • Installation shall be performed by ASCC trained and approved installers. Maintenance where required shall be in accordance with the ASCC Building Product Quality Plan ver 2.1
Statement of Building Code Compliance

Complies with the New Zealand Building Code:

  • Performance Clauses B1.3.2
  • Performance Clauses B2.3.1 (a)
  • Performance Clause F2.3.1
  • Performance Clause H1.3.1
In-Service History

A two hut field exposure comparison conducted in Ontario, Canada Field, investigated the heating energy consumption of test huts insulted with either spray foam or fibreglass batts.

Click the Case Study link under Literature to see the full report.

Other Performance Attributes
  • Stable thermal performance
  • R-value = 3.13 at 70mm
  • R-value = 3.57 at 80mm
  • R-value = 4.46 at 100mm (click here for full R-value table)
  • Good sound control
  • Maintains an air seal even after seasonal expansion/contraction of building assembly
  • Less than 1% water absorption
  • Supports indoor air quality by blocking air infiltration and mass transfer of moisture that may cause mould
CodeMark
CodeMark
Test Results
Test Results
Documents
Building Product Quality Plan 2.1
Data Sheet
R-Values Table
Appraisal, Accreditation, Certification and Testing
CodeMark Certificate
Technical Manual
Case Study: Two Hut Field Exposure Comparison
Watch Video: The Next Generation in Insulation
CAD/PDF Details
Typical Cross Section

Spray foam insulation is the most effective and efficient insulation in the market; it is safe, environmentally sound, non-allergenic, and dust and fibre free, and saves money by stopping heat loss.

Product Enquiries

News from NZ Foam

A Cost-Effective Option for Insulating Skillion Roofs
NZ Foam: An Efficient Choice for Repurposing Old Sheds
Foam Insulation Keeps Sheep Shelter Condensation-Free
Get a free weekly digest of essential news

New and updated architectural products, design solutions, inspiration, technical advice and more when you sign up for EBOSS.